ENGINE / TRANSAXLE. AIR INTAKE. 4. 2 liter.. 2010 Audi S5

4.2 LITER. Air cleaner assy.

4.2 LITER. Air cleaner assy grommet. Air Filter Housing Grommet. Air Filter Housing Insulator. Grommet through which a portion of the expansion tank fits when mounted to vehicle. Cleaner Assembly Insulator. Engine Coolant Recovery Tank. Filter Housing Insulator. Mount bushing. Reservoir cap. Included with: Air Cleaner Assembly.

4.2 LITER.

4.2 LITER.

4.2 LITER.

4.2 LITER. Air mass sensor seal. A circular disk covered in rubber or plastic with a hole in the center where the edge is sometimes tensioned by a spRing that prevents fluid from leaking at the Mass Air Flow Sensor. A round Ring used to Seal between the Air Intake Duct and it's mounting surface. Engine Air Intake Hose Seal. Fuel Injection Air Flow Meter Gasket / O-Ring. Mass Air Flow Sensor O-Ring. Part inscluded with Connector pipe. Rubber Sealing Gasket that fits between the Engine Air filter housing rear cover and the Engine Air filter housing. Cleaner Cover Gasket. pipe inner. Adapter o -. Engine Intake Hose O -. Filter element outer. Fuel Injection Flow Meter Gasket / O -. Inlet tube. Intake Duct. Mass Flow Sensor O -. Included with: Air Cleaner assembly, Connector pipe.

4.2 LITER. Air mass sensor screw. A screw that is used to secure the Mass Air Flow Sensor to its mounting point. Engine Air Intake Hose Screw. Flow. ADAPTER. Connector. Engine Intake Hose.

4.2 LITER. Hose. Engine Air Intake Hose. Part number is for 5 meter coil, cut to correct length. Vacuum Hose. Vacuum Line. Included with: Air cleaner assembly Cut as required, Air cleaner assembly Part listed is for 5 meter roll Cut as required, Part is cut to fit Air cleaner assembly.

4.2 LITER. Hose retainer.

4.2 LITER. Adapter. A bracket for a air cleaner. Bracket used to secure the expansion tank to its mounting point. Engine Air Intake Hose Adapter. Coolant Reservoir. Intake Hose. Mass Flow Sensor.

4.2 LITER. Adapter bolt. A Bolt used to secure the brake dust shield to it's mounting point. A Bolt which retains the convertible top catch to its mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Convertible Top Mounting Plate to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the EGR Valve Cooler to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Quarter Panel Glass Guide to it's mounting point. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Turbocharger Heat Shield to a mounting point. ABS Modulator Bolt. Air Filter Housing Bolt. Bolt for the brackets that hold the Radiator Hose. Bolt that fastens Heater Hose to vehicle. Engine Air Intake Hose Bolt. Engine Air Intake Hose Screw. Engine Coolant Reservoir Bolt. Hardware to attach the Heat shield to the catalytic converter. InterCooler Pipe Bolt. Interior Quarter Panel Trim Panel Bolt. Part cannot be reused/reinstalled. Window Regulator Bolt.

4.2 LITER. Intake hose.

4.2 LITER. Intake hose clamp.

4.2 LITER. Intake pipe.

4.2 LITER. Intake duct.

4.2 LITER. Intake duct screw. A Screw used to secure the Engine Air Intake hose debris screen to its mounting surface. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Air Intake Hose Debris Screen to it's mounting point. Engine Air Intake Hose Bolt. Engine Air Intake Hose Screw. Quarter Panel Trim Panel Screw. Trunk Trim Panel Screw. guide. Hose Debris Screen Bolt. inlet duct. Manifold. Quarter Panel Panel. Strainer. Trunk side.

4.2 LITER. Intake duct U-nut. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Floor Pan Splash Shield. Engine Air Intake Hose Nut. Spoiler Nut. Air guide U -. Air inlet duct U -. Engine Air Intake Hose. Floor Pan Splash. Heat. Manifold U -. Outer cover U -. Side Spoiler. Speed.

4.2 LITER. Strainer.

4.2 LITER. Strainer screw. A Screw used to secure the Engine Air Intake hose debris screen to its mounting surface. A threaded rod with a drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Air Intake Hose Debris Screen to it's mounting point. Engine Air Intake Hose Bolt. Engine Air Intake Hose Screw. Quarter Panel Trim Panel Screw. Trunk Trim Panel Screw. guide. Hose Debris Screen Bolt. inlet duct. Manifold. Quarter Panel Panel. Strainer. Trunk side.

4.2 LITER. Boot.